Zusätzliche elektromechanische Signaleinrichtung für den Telefonbetrieb.
Durch das elektromechanische System sehr laute Signalisierung.
FUNKTION
Elektromechanischer Aussenwecker
WK 971
- Zweitonklang
-...
Part no.:
71231
Herst.Art.Nr.:
1-509.15.1.11
stock:
0
This product is not available at the moment. Delivery time upon request.
Unterputz-Anschlusseinheit Cat.3 mit zwei einzelnen RJ45-Buchsen
UAE design 8/8(4) und UAE design 8/8(8) für den steckbaren Anschluss von zwei Terminals (Telefon, Telefax etc.).
Die Entriegelungshebel der Stecker zeigen...
Part no.:
72642
Herst.Art.Nr.:
130064102-I
stock:
0
This product is not available at the moment. Delivery time upon request.
Kanal-Anschlusseinheit IAE design 8(4) und 2x8(4) für den steckbaren Anschluss von ein/zwei ISDN-Terminals (Telefon, Telefax)
Entriegelungshebel des Steckers zeigt bedienungsfreundlich nach oben. Durch die 45°-Steckrichtung fällt die...
Part no.:
72643
Herst.Art.Nr.:
130040112-I
stock:
0
This product is not available at the moment. Delivery time upon request.
B600xH1300xT240mm, Geschlossener Stahlblechschrank mit Schwenkhebelgriff für Profilhalbzylinder, Kabeleinführung oben und unten über Bürstenreihe, Farbe: RAL7035, lichtgrau, Schutzart IP40,
Part no.:
91609
Herst.Art.Nr.:
46076.1V2
stock:
0
This product is not available at the moment. Delivery time upon request.
A resistor has a defined conductivity, which determines the current when voltage is applied. The maximum load is important, which is converted to heat for our resistors this should not be more than 1/8W.
Part no.:
113648
Herst.Art.Nr.:
ALL-BRICK-0021
stock:
0
Ready to ship today, Delivery time appr. 1-3 workdays
The ground enables the voltage back and forth. Put it to the ends of cicuit to close the power circle. It connects the middle connectors to the outer ground connectors.
Part no.:
113630
Herst.Art.Nr.:
ALL-BRICK-0003
stock:
0
Ready to ship today, Delivery time appr. 1-3 workdays
The red LED (light emitting diode) is protected by a series resistor against overload. It only lights up if the diode is connected in flow direction, i.e. current flows from anode to cathode. The LEDs need minimum voltage in flow...
Part no.:
113636
Herst.Art.Nr.:
ALL-BRICK-0009
stock:
0
Ready to ship today, Delivery time appr. 1-3 workdays
The green LED (light emitting diode) is protected by a series resistor against overload. It only lights up if the diode is connected in flow direction, i.e. current flows from anode to cathode. The LEDs need minimum voltage in flow...
Part no.:
113639
Herst.Art.Nr.:
ALL-BRICK-0012
stock:
0
Ready to ship today, Delivery time appr. 1-3 workdays
This building block has two LEDs, a red LED for control and an infrared (IR) LED, which cannot directly be seen by us, approx. 900nm. However, it can be seen in most cases with a camera. Both LEDs are protected by a series resistor...
Part no.:
113640
Herst.Art.Nr.:
ALL-BRICK-0013
stock:
0
Ready to ship today, Delivery time appr. 1-3 workdays
Our switch includes three different states: In the middle state, all contacts are separated. In the left state, there is a connection between the middle and the left. And in the right state there is a connection between right and...
Part no.:
113645
Herst.Art.Nr.:
ALL-BRICK-0018
stock:
0
Ready to ship today, Delivery time appr. 1-3 workdays
A resistor has a defined conductivity, which determines the current when voltage is applied. The maximum load is important, which is converted to heat for our resistors this should not be more than 1/8W.
Part no.:
113649
Herst.Art.Nr.:
ALL-BRICK-0022
stock:
0
Ready to ship today, Delivery time appr. 1-3 workdays
*Auftragsbezogen, nicht Stornierbar*,
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX:
half or full; 1000BASE-T: full only...
Part no.:
114335
Herst.Art.Nr.:
JG225A
stock:
0
This product is not available at the moment. Delivery time upon request.
A resistor has a defined conductivity, which determines the current when voltage is applied. The maximum load is important, which is converted to heat for our resistors this should not be more than 1/8W.
Part no.:
113650
Herst.Art.Nr.:
ALL-BRICK-0023
stock:
0
Ready to ship today, Delivery time appr. 1-3 workdays
A resistor has a defined conductivity, which determines the current when voltage is applied. The maximum load is important, which is converted to heat for our resistors this should not be more than 1/8W.
Part no.:
113651
Herst.Art.Nr.:
ALL-BRICK-0024
stock:
0
Ready to ship today, Delivery time appr. 1-3 workdays